went through the gamepad setup in EmulationStation for both gamepad devices.(which was apparently a mistake because now run command pops up the launch menu every single time, so that's something else to fix now) reset EmulationStation inputs via retropie-setup.set all the pins to the appropriate gamepad buttons.re-flashed the UltimateIO with the dual-GP firmware.There's a note on git about using -e to specify an input event to bind to, but the binary doesn't recognize -e as an option, and all it will say is that xarcade isn't detected, retrying (forever). Out of the box (or make anyway) it's looking for the xarcade, which isn't there. I built and installed xarcade2joystick from the latest. That would be a great benefit if it worked, but it does not. I've tried just using a keyboard, which functions exactly the same as the joystick (c/v are coin/start, 5/1 do nothing).I've verified that the buttons themselves do work (they work perfectly and as you'd expect in Mame2003, 2010, and AdvMame).I've remapped a whole bunch of buttons to "5" in the hopes to just see it work for ANY remap, and so far no effect.I've tried flipping from "5" to "num5", and so forth.didn't work, and not my preferred method anyway. I've mapped the coin/start keys to L2/R2/元/R3 in EmulationStation, and then tried setting joypad input in Retroarch and mapping them that way.The core remap file loads as expected when I start a new game, but has no effect. Select and Start are still tied to v/c/l/j and still work. The problem is that it doesn't DO anything. I see the inputs set as key codes (53/49 and 54/50) which I understand and expect. So I see the input device for P1 and P2 set for 3 (Keyboard). Here's entirety of the remap file after I make those changes (only) and hit save: input_libretro_device_p1 = "3" I set Select and Start to 5/1 and 6/2 respectively and save the core remap file. I have all the various keyboard inputs available to me in the input remapper screen. Since I have specified keyboard input with this: input_libretro_device_p1 = 3 So I follow the various guides to Core Input Remapping. They correspond to the following keystrokes: That catch is that, for FBNeo only, I want to use my dedicated Coin and 1-Up buttons instead as select and start. Select/Start work as COIN1/P1_START in FBNeo, which is great. Here is the relevant section of all/retroarch.cfg: input_libretro_device_p1 = 3Īt this point, everything works fine for most emulators, and I don't want to change it. I wouldn't think it matters, but someone said it did once. Being on an UltimateIO, my buttons are keyboard keys.RetroPie 4.5.1 on a Pi3b with an UltimateIO encoder. I have seen lots of guides and advice which make sense, but don't seem to work. There's one thing that's frustrating me, though, and that's core input remapping for FBNeo. Please also make a back up of your configs before changing them.I'm somewhat new to this, but managed to get most everything working just like I like it. That should be all you need to do unless you want to add players.Īs I may have said already, you don't normally have to remap controls if using an Xinput controller as they should already be set up. Do the same for the other inputs and then scroll up to "User1 Save Autoconfig". Highlight this and press X to remap the button. To the right of that is the button or keyboard assignment for your controller. Now you will see the inputs for the Genesis controller on the left, so User 1B is the player 1 B button on the original Genesis controller. I used an Xbox360 controller for this test. In the next menu you should see your controller listed maybe as Xinput, if it's not listed then maybe RetroArch has not detected it, try cycling through the options. Scroll down to the User Input Binds 1 and hit the X key to enter. In the next shot I have disabled "AutoconfigEnabled" as this worked for me, but may be different for others. Hit F1 to enter the menu and move across to settings and then input. So run a game for the system you are setting, here I chose Sega Genesis. If you create a new post then the people following will be emailed.īelow are the steps I take when remapping controls on my cab for my Ultrastiks, it also assumes that you have per system configs set up. First of please do not edit your post with important information if you want people who are following to see it.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |